Sabre Tooth Traffic Controllers
enforce "One Way" traffic
flow for parking facilities or
other single direction vehicle
lanes.
The torsion spring actuated sabre
teeth positively control traffic
in one direction while permitting
free flow in the other direction.
The Sabre Tooth will puncture
all pneumatic tires including steel
belted radial and large truck tires.
Note: Before
installing the Sabre Tooth Modules,
it is mandatory to read the Instructions
and Safety Pre-Cautions. The
Latch Down and Bumper Kit Options
cannot be combined on the same
traffic unit. |
 |
TC3
Sabre Tooth Conversion Modules
The
TC3 Sabre Tooth Conversion Modules
are designed to convert obsolete
spring wire controllers to Sabre
Tooth operation. The
drawing shows a module in place
on a P-O-M frame.
Adapter strips are welded to existing
I-ground frames and then modules
are bolted to strips.
- Module size 12 inches long
x 8.5 inches wide
- Adapter strips 72 inches wide
and 12 inches long
- Three Sabre Teeth per module
- Long life torsion springs
- Top plate - Alert Red, Teeth
- Zinc plated
- Weight 120 pounds, approximately
- Latch Down mechanism available
|
 |
TC8
The
TC8 is designed to mount on an
existing drive or ramp (concrete
or asphalt) with bolts or epoxy
to eliminate excavation and drainage
problems. By
installing units end to end, any
width driveway can be controlled.
- 36 inches long x 20 inches
wide x 2 inch high (teeth depressed)
- Overall height 4.4 inches
(teeth extended)
- 3 removable and reversible
3 tooth modules (12 inches long)
- Long life torsion springs
- All welded steel frame (.250
plate)
- Body - Alert Red, Teeth -
Zinc plated
- Weight (36 inch unit) 155
pounds, approximately
- Latch down mechanism available
|
 |
TC12
Shallow Frame Sabre ToothT Controller
Flush Mount
- 72 inches long x 8 inches wide
x 1.5 inch deep
- 3 Tooth modules (12 inches long)
- Long life torsion springs
- All welded steel frame
Reinforcing bar runners on each
side of body for pull strength
- Top plate - Alert Red, Teeth
- Zinc plated
- Weight 20 pounds per module,
approximately
Latch down mechanism available
|
 |
TC14
The
TC14 Standard is named as such
because it is “The Industry
Standard.”
- 72 inches long x 10 inches
wide x 4.2 inches deep
- 20 Sabre teeth (3/8 inch steel
plate)
- Teeth sprung in pairs
- Long life torsion springs
- All welded steel frame (.188
plate)
- Top Plate - Alert Red, Teeth
- Zinc plated
- Weight 130 pounds, approximately
- Special latch down units available
Shallow Frame
- 72 inches long x 8 inches wide
x 1.5 inch deep
- 3 Tooth modules (12 inches
long)
- Long life torsion springs
- All welded steel frame
Reinforcing bar runners on each
side of body for pull strength
- Top plate - Alert Red, Teeth
- Zinc plated
- Weight 20 pounds per module,
approximately
Latch down mechanism available
|
 |
TC20
Non-Penetrating Traffic Barrier
Flush
Mount
The TC20 stops
wrong way vehicles by locking
its barrier strips into an upright
position. The
locked plate modules form a steel
curb over which a wrong way vehicle
must pass. These
barriers stop all but the most
errant driver. The
barrier plates have rounded corners
for pedestrian traffic.
- 72 inches long x 10 inches
wide x 4.2 inches deep
- Long life torsion springs
- All-welded steel frame
- Top plate - Alert Red, Teeth
- Zinc plated
- Weight 145 pounds, approximately
|
 |
TC22
The
TC22 combines all the features
of the TC20 above but in a surface
mount configuration. It
mounts on an existing drive or concrete
or asphalt ramp, eliminating excavation
and drainage problems
- 36 inches long x 20 inches wide x 2 inches high
(barrier strips depressed)
- 3 removable and reversible 3 tooth modules (12
inches long
- Long life torsion springs
- All welded steel frame (.250 plate)
- Top Plate - Alert Red, Teeth - Zinc plated
- Weight (36 inch unit) 130 pounds, approximately
- Latch down mechanism available
|
 |
TC28
The TC28 is designed to handle
extra heavy industrial traffic. Locations
where axle loading exceeds known
highway specifications are easily
handled by the TC28. The
unique design of the Tandem Tooth
incorporates extra strength axles,
top plates, frame supports and anchor
tabs.
- Frame dimensions 72 L x 10 W x 4.4D (inches)
- Allowable load 40,000 pounds
- Long life torsion springs
- All welded steel frame
- Flush installation (bolts recessed)
- Top plate - Alert Red, Teeth - Zinc plated
- Frame epoxy undercoated
- Shipping weight 150 pounds, approximately
- Latch down mechanism available
|
| 
